Thursday, October 31, 2019

The Achievement of Success in an Individuals Life Personal Statement - 5

The Achievement of Success in an Individuals Life - Personal Statement Example I chose the difficult path because I understood that education and knowledge serve to be important in the life of a person. I put in all my strength to cope up with the educational requirements of the university and I was assisted by my faculty members, who understood my problem and were highly supportive. English is not my first language and I did not hold much expertise in the language. I got enrolled in an English University where English was the medium of education. The lectures were delivered in English and English was the language used for communication with the teachers as well as the other students. The books were in English as well. My English language skills were not very good and it was a very difficult phase for me. This was because my writing, reading as well as communication skills were not up to the mark and I had to put in much hard work to cope with my studies. I found it difficult to take down notes during the lectures. This was because I had to pay full attention t owards listening to the teacher to understand the lecture and if I started taking notes, I used to lag behind in the lecture. Note taking was also an issue as I could not spell words properly and my writing speed was not up to the mark as well. I could not understand the normally used abbreviations as I was not familiar with them and had not used them before. The text was also difficult for me to comprehend with and I could not analyze the meanings of the readings assigned to me properly. Therefore, it was a very difficult situation for me and I needed a lot of guidance and help to overcome this problem. I did not know if I would ever be able to complete my education and achieve my degree from the university. But after thinking about my problem, I became determined that a person had to sacrifice and learn for becoming successful in his life. I decreased my leisure time and devoted my time to my education and learning. I organized myself and managed my time so that I could give the m aximum time to my studies. I bought a pocket dictionary for myself so that I could look up for words and understand them instantly. I installed English learning software in my laptop as well so that I could learn the proper pronunciation of words as well and so that I could learn proper sentences and their meanings. I asked my friends to communicate with me in English and correct me where I got wrong. I kept a fixed time for reading a newspaper article every day and to understand all the words in the article. I also worked towards the improvement of my writing skills by copying newspaper articles every day for up to one hour. I implemented these strategies as a part of my schedule and I made sure that I did not skip any of these activities. These were my personal steps to achieve success in my education. Teachers serve to be as true guides in the life of a person. This was proved by the assistance that was provided to me by my teachers to overcome my problem.  

Tuesday, October 29, 2019

Why I want to attend a particular law school Essay

Why I want to attend a particular law school - Essay Example To begin with, I am convinced that I am an excellent match for the Harvard Law School Program on International Financial Systems (PIFS), since the program has been instrumental at inculcating exchange of ideas as well as research on capital markets, financial regulation, and international financial systems. With my Bachelor’s degree in Finance, and my keen interest towards the international law realms, I have undoubtedly looked into a number of law schools and found that Harvard Law School’s PIF, being run by acclaimed professor Hal Scott is an exceptional blueprint, which offers a more comprehensive study of international finance than any other law school. It gives me more reason to be genuinely excited about the possibility of participating in Harvard Law School’s global international legal studies outside the classroom. Specifically, the international learning possibilities afforded by attending the Graduate Institute of International and Development Studies in Geneva, Switzerland appear sizeable when I contemplate such measures. My personal commitment towards improving the conditions in Tanzania and east Africa, as discussed in my personal statement, would greatly be facilitated by my studies of the World Trade Organization law and the United Nations law, besides international finance and economics. Harvard Law School has a universal appeal to an individual who is looking to attend a law school, as well as to any organization or agency, which is looking to hire the sharpest legal minds. I would be most pleased and honored to be a part of the Harvard Law School’s younger demographics, with decades ahead of me to hone my legal skills and to become a scholar in a field that will only continue to grow and develop as international expertise in the

Sunday, October 27, 2019

a suitable function of construction industry

a suitable function of construction industry Introduction Until 1958 when the construction industry began to be formulated following rules, construction businesses had suffered a poor reputation due to wrong practices of the past. The construction industry was known as an area of illegality and corruption. Accordingly, it is no exaggeration to say that for Korea’s construction industry, the past six decades were characterized by a war against illegality and corruption. Ironically, the response to this was the introduction of the American type of construction system. In addition, it is notable that competition has been introduced for construction project bidding. To be sure, there were limitations in rooting out illegality and corruption. Through these efforts, however, the nation could establish a modernized delivering system for construction projects over the year. Additionally, it is not too much to say that policy and system were formulated. In meanwhile, large-scale construction accidents frequently occurred due to dishonest work , which will happen in the process of industrialization. In April 2002, the South Korea government announced that it will work more closely with non-governmental actors in the fight against corruption. The government procurement agency announced the introduction of an ombudsman system and a clean procurement committee in an effort to break ties between the government and its contractors. The corruption law also established an anti corruption commission, with a specific mandate to investigate cases involving high rank officials. Before the commission was launched in January 2002, however, its first chairman resigned because of his suspected involvement in a major corruption. Like this, corruption is occurring by human selfishness. There were many accidents through human errors and misdeeds. Sampoong Department Store is one of the examples. On 29 June 1995, a department store building in Seoul suddenly collapsed. It was only five years old and killed 502 people and injured 937 people. The structural collapse of the Sampoong Department Store was not an isolated deviation but a clear omen of deeper problems within society. In the Sampoong collapse, bribery of inspectors was rampant. No one raised any alarm when a huge, unauthorized air-conditioner was erected on the roof of the building which caused enormous cracks in the walls. A probe revealed that the building’s owners sacked contractors who had complained that planned design changes were unsafe. The new contractor, a subsidiary of the store, had no objections. In this accident, at the same time, South Korea’s construction industry had been attacked by man-made disasters even before the Sampoong Department Store tragedy. In this paper, the main reasons of the collapse and evaluation of this collapse will be briefly described. Background The Sampoong building had two wings, with one housing the department store and the other sports and leisure facilities. The wing that collapsed was the one housing the department store. It was built by Sampoong Construction and Industry Company and completed in November 1989. An addition to the building was completed in October 1994. The building housed 556 departments with 681 employees. It stood 27.6 meters high and sat on a 29,008-square-meter.The four underground floors consisted of a parking place and an electricity control room. Three of the collapsed building’s floors which comprised the department store was operated by Sampoong Construction Company whose engineering ranks 858th among the nation’s construction firms. If it was careful, the warning signs that could have prevented the collapse of the Sampoong Department Store came as early as 15days before the accident. At that time, a restaurateur on the fifth floor reported a crack on the ceiling of the building to management. But, management’s response was lukewarm, and management took no action. Then, 5 days before, a customer who had entered the same restaurant to get something to eat after some routine weekend shopping, was showered with a water leak from the ceiling of the restaurant. Three days before the collapse, a report of a gas leak again went unheeded by the department store management. On the day of the collapse, June 29, the signs that should have set off alarm bells appeared before opening hours in the restaurants on the fifth floor. Around 9:30 a.m., the floor of the restaurant cracked open slightly. An environmental technician reported the incident to the management. Top executives of the department store stopped by an hour later, mumbling something about seeking professional assessment. Between 11a.m to 12p.m, neighbouring restaurants were experiencing water leaks from ceilings and cracks in the floors. Only at this point did the management close off the fifth floor, while the other floors continued with business as usual. Sometimes after 1 p.m., a breakdown of air conditioning and gas services as well as a power failure occurred throughout the department store. The management met around 3 p.m. for an emergency meeting without notifying the employees and shoppers of the situation. When things were at their worst, the executives of the department management lef t the building, consequently leaving many employees and shoppers still inside. At 6p.m. on 29 June, the centre of the building collapsed, similar to a controlled implosion, in 20 seconds. Customers were concentrated in the basement and in the fifth floor restaurant. The customers and employees had no time to escape. Some survivors were found in the wreckage, and one was brought out 17 days after the collapse. The overall death toll was 502. Corruption The main issues addressed in this paper are corruption, frequent design change and maintenance repair in South Korea. The first section of this paper will examine corruption in the collapse of the Sampoong Department Store. This report was delivered by Seoul District Prosecutors Office, entitled The Final White Book of Finding out the Real Truth of the Collapse of the Sampoong Department Store. The public was outraged. In particular, the news that the senior executives had fled the building without warning others was disturbing. The report on the collapse, as well as earlier structural and construction failures, suggested a widespread pattern of corruption in the country’s construction business. A government survey of high-rise structures found 14% were unsafe and needed to be rebuilt, 84% required repairs, and only 2% met standards. Joon Lee, the chairman of Sampoong, and his son Han-Sang Lee, were convicted and sent to prison for 10 and half years and 7 years, respectively. Twelve local building officials were found guilty of taking bribes of as much as $17,000 for approving changes and providing a provisional use certificate. The cause of the Sampoong collapse, then, was not a technical issue as much as outright fraud. The Korean construction industry, protected by government regulation from outside competition, had become complacent. Bribes were used to get around the usual government checks and balances that serve to protect public safety. Relationship problem between the architects and builders In the design planning process, relationship and communication between architectural designers and structural designers are important. Generally, if their relationship and communication are in discord some construction works, it can bring out accidents such as Sampoong Department Store collapse. This paragraph begins by laying out the theoretical dimensions of the research and looks at how design problems occurred in this collapse. In recent years, the subject of the design quality has become one of the important issues in the domestic construction industry. However, important design processes are made by judgement of the architect without the rational communication and information sharing among the related participants. Therefore, the objective of this research suggests the constitution plan of design error management system not only for systematizing types about the design error in construction projects but also for analyzing the primary factors of design error to embody the actual condition of trouble between architects and builders. Normally, in South Korea, builders think know-how is more important but architects think that beauty of art and quality what contractor ordered, are more important so that there were lack of communication of information and a narrow sense between architects and builders. Relationship and communication problem between architectural designers and Structural designers Generally, design drawings are distributed, such as architectural design drawing, structural design drawing, mechanical facility design drawing, electric facility design drawing and engineering design drawing. Structural calculations need to be correct in order to ensure the safety of the building and structural design drawing with structural calculations need to be written exactly and used on-site. Mechanical facility and electric facility design drafts are written considering the calculations which were reviewed in advance about facility capacity or standards according to the structure calculations in the structure design drawings which include the safety of a building and standards. In the process of structural design planning which affected the most important reason of the collapse, architectural designer and structural designers decided the scale of a building, stories, appearance and use in the early architecture plan and then on a basic structure plan like pitch of columns or structure style. The architectural designer writes the architectural design draft first, and the structure designer carries out structure calculations according to all conditions given in the architecture blueprint which the architectural designer wrote. In many cases, however, architectural designers distribute structural design drafts which are calculations made by structural designers. As the result, structural designers are different with structural draft authors, so that structural designers’ design can be changed by authors who may make fatal errors. In this accident, it the relationship and communication between architectural designers (architect) and structural designers (structural experts) was not adequate, and their communication was only call and memoranda, so that they had not exchanged information. Thus, structural calculations, structural drafts and construction drafts were different. Design problems There were many structural and architectural problems in the Sampoong Department Store collapse. This paragraph will describe problems of use change and flat slab systems in the problems. Firstly, construction of the Sampoong Department Store was a flat slab system. The flat slab system can be defined as a construction method that builds safely several columns established in the upper part inside of the building. However, the weak point of this system is many columns. So, this flat slab system is insufficient to department store buildings because if there are lots of columns in the building, the space will be narrow. So, structural designers removed block walls for the purpose of making wide clearances to sell products and punched a passage for an escalator. Also, size and shape of uplift column was changed. In flat slab system, the column is very important but structural designers of Sampoong Department Store had neglected design load calculus. Moreover, even though the fifth floor was made, column size was lessened 25% (79cm to 58cm) for appearance and even columns located near the escalator were lessened more. Secondly, the use of the Sampoong Department Store was four stories office building at first and this building was approved as a four stories building. However, owners of the building wanted to change to a department store building and the owners referred it to Woosung Construction Company. Constructors and managers of Woosung Co. opposed that because it needed more columns and thicker columns. Thereupon, the head of the Sampoong group changed Construction Company to own Sampoong Construction Company. Lastly, the five stories Sampoong Department Store were built without reinforcement of uplift columns by the company. The most serious problem was the fifth floor. The fifth floor was the restaurant area and the interior was composed of a Korean floor heater for a luxury Korean traditional restaurant so that, 30cm concrete was added for the Korean floor heater. Also, heavy kitchen equipment was needed. As the result, the whole building collapsed when these added loads affected columns. Maintenance problems This paragraph explains the maintenance of collapse of this Sampoong Department store. Sampoong made significant changes to the structure. The most important was the conversion of the original use as an office block to that of a department store. Other changes included changing the upper floor from a roller-skating rink to a traditional Korean restaurant. Stricter standards had to be met for fire, air conditioning and evacuation. Although the structure apparently met all building code requirements, the revised design was radically different from the original. This accident was a man-made disaster that the government official allowed haughty businessman who brought out blind money as a result and the building company built it. Conclusion The construction work of Sampoong Department store was started on July 1987 and opened on December 1st 1989 with Temporary Use Permit and operated for 5 years. Unlike a normal building framework using beam and column, its structure system uses Flat Slab structure so that the floor slab supports the column by itself without any beam. In a flat Slab structure, one column can stand the same amount of stress so that the collapse of one column can cause progressive collapse which can be them the entire building. Investigating the present state of collapse was analyzed minutely and based on this analysis, the design, construction work, and maintenance of this building was discovered as the direct and indirect cause of collapse. As a result, the collapse of this building was brought from a flaw in design, unreliable construction work, and maintenance problems interacting with each other for long term. A brief summary is the following. Firstly, the one that influenced collapse the most is the maintenance problem. Changing design and use, without any approval, causing additional overweight to be added and also cutting structures left the whole building structure with low durability. Secondly, in the process of construction work, managing the work and superintendence was negligent which caused part of the collapse. Thirdly, inappropriate construction and structure plan caused progressive collapse. Moreover, neglecting safety diagnosis on the long term cracks and sinking process and insufficient managing of crucial moments like right before the collapse brought about a disastrous accident. Finally, those causes, which continued for 5 years, gave no security and safety, and at the end, around the fifth floor, the roof slab was destroyed and the adjoining slab destroyed, which caused progressive collapse. A building can maintain safe conditions through fine design, construction work/supervision and appropriate maintenance. However, if a domestic construction system does not include a structure expert who puts safety first anywhere in the process of design, construction work/supervision and maintenance, there will be major problems. According to the law for architect, article 4 clause 1 and clause 2, designing and supervision of construction can only be done by an architect, and blocks the structure expert from designing and supervising the construction from the beginning. In addition, the law for architect article 2 clause 2 states that structure expert has subordinate relationship with architect, so that structure expert is not at the position where he can take responsible for the safety. Such a system cannot be found in developed countries except in Korea. For example, America does not limit the construction right to either architect or structure expert and Germany gives right to design structure only to structure expert. Also, Japan and Singapore structure expert takes care of structure design. Especially in Germany and other EU, client or representative picks ‘safety coordinator’ who takes charge of every process from beginning to the end, such as consulting and superintendence. To look at design, construction work/supervision and maintenance of Sampoong department store closely, structure expert was never in the responsible position so that he did not finish his work with responsibility. Moreover, the current domestic system had no coordinator who could point out faulty structure design and construction so that an architect who was responsible for construction asked the structure expert only for structural calculations and used them on the structure layout. When use and design were changed, the architect only asked the structure expert orally or in memo form and not with any official document. It seemed that structure expert was legally only in an assistant position which made it harder to ask for formal documents and the structural expert also did not have any obligation to be responsible for the structure problem since they are only an assistant. Recently constructions with size over fixed standard or for special needs are required to have affixing a seal of structure expert on the structure layout. However this is only the action of affixing a seal from the structural expert, it does not mean that they are responsible for construction like in other developed countries. In Korea, the current system does not have any way to prove the faulty safe the issues from in the process of design, approval, and construction/supervision like Germany or EU. In the deliberation for a Construction Permit, structure field is handled but it’s only 10 or 20 minutes which is impossible time to point out any problem in the structure and examine an entire complex design perfectly so that the Construction Permit is only a formal document to avoid responsibility. In conclusion, although common administrative regulations should be softened in order to solve inconvenience of the people and the vitalization of market, strengthening the regulations to protect the nation and their property is a global trend. To take this into consideration, experts who can take care of their work with responsibility and specialty is essential and needed on every step in the process of design, construction/supervision, and maintenance in order to prevent the reappearance of such a disaster like the collapse of the Sampoong department store.

Friday, October 25, 2019

John Logie Baird and the Television :: essays research papers

John Logie Baird and His Miraculous Television Advancement Born and raised in Scotland, John Logie Baird received a science degree and took an engineering job. At twenty-six years old Baird decided he didn’t like his job, so he quit and decided to become an inventor. He spent nearly ten years producing failed inventions then he put full thought into television development. By the end of 1923 John Logie Baird, through sheer determination, had finally managed to build what were effectively the world's first complete television transmitter and receiver. The first image that was transmitted was a plain cardboard cross, the camera and transmitter being just a few feet away on the other side of the room. Public interest grew greatly in January 1924 when Baird's success was reported on by the Daily News. But because Baird had electrocuted himself twice and caused a small explosion during this process, Mr. Twigg, the landlord, evicted John Baird at this time. John Baird moved to London in August of 1924 and then in April of 1925 he showed his Televisor at Selfridge's Department store. Viewers gathered in a small dark room, to strain their eyes and see a flickering, but nonetheless miraculous image of a doll on a screen of about four by two inches. Though not much more than the shadow of the doll, the image represented a significant achievement. This was the first time a picture had been created from reflected light. "The image of the doll's head formed itself on the screen with what appeared to be an almost unbelievable clarity. I had got it! I could scarcely believe my eyes and felt myself shaking with excitement," said John Baird. In October 1925 Baird succeeded in transmitting full television images. These were real television pictures which picked up reflected light and showed light and shade effects. The first human being to be televised was a frightened teenage office boy, William Taynton, who had to be bribed to stay under the hot lights. At that time there were no moving images. Baird's scanning discs and photo electronics were to slow and insensitive to capture moving objects. But now that has all changed now that he got upgrades. This year on January 26, 1926 Baird showed a fully working prototype of mechanical television to members of the Royal Institution.

Thursday, October 24, 2019

Cost Of Goods

The cost of making the product is an expense to the business and reduces the profit that the company can make when selling the products. The COGS is calculation once a year by showing charges from the Start to the end of the company fiscal (financial) year.In calculation the COGS you need to include cost of producing the product, wholesale price of good resold and what the direct manual labor cost the company makes the product. The other costs to be calculation is cost of containers, freight, rent, utilities, shipping and overhead. Whenever the COGS increase the net income is less. The sales of products need to be kept down to increase the profit. Inventory also determined the COGS by it changes of the product that was sold at the beginning of year and the inventory at the end of the previous year is calculation.The cost of goods purchased and made during the year is added up and the inventory at the end of the year is subtracted. This calculation is done so the company will know how much the inventory cost and how much was sold by the company during the year. The inventory is reported at the cost to make or buy the product, it is not the cost to sell it. If sells items cost change during the year, the company much figure out a transaction to deal with those cost changes in a way suitable to the IRS. It would have to figure this change into their COGS equation.The IRS has quite a few standard ways to account for changes in cost through the year without having to track each product price separately. 2. Record the transactions HTH made the purchase and sale of merchandise. All sales transactions have a credit entry to the sales account. The other transactions depend on the particular situation that is surrounding that transaction. There are make ways a company can makes sales and it can have a impact on an transactions sales. The sales can be for cash, resulting in a debit to cash or credit, which can lead to a debit to account receivable.The companies that use t he cash method receive sales only when actual cash have been received. When using the accrual method record the sales the moment the sale is made regardless of payment. In a permanent inventory system every entry for a sale must have a matching entry cost of goods. Using this system you have to book a cost of goods transaction for every individual inventory item you sell. The periodic systems from beginning to end on cost of goods entries are recorded during the accounting period, resulting in single -entry sales transaction.Once a business chosen an counting system that method dictates that part of the entry all the time. In a cash system you cannot ever record a sale transaction until the money has been paid. A cash or credit transaction may be different because it depends on the actual sales. Also there are risks when using cash sales and credit sales. When using the cash sales you get paid right then there is no waiting to receive your money in cash or credit card. With credit s ales the company extend credit with agreement of to be paid later and the business run the risk that the customer may not pay the money on time or pay not at all.It is very important when using the cash or credit system for a transaction the company needs to keep a record Of it (document) so the detail can be found of the transaction. The detail should include sales receipt with date, description of what was sold and the amount of the item. But credits sales are (not credit card sales) are treated just like a cash sales. The source document is done on a invoice slip it include all the information as the sale receipts and much more it have the purchaser name, contact information, credit terms due date, account number, purchase order number and invoice number.These record much be kept straight this should be done by premiered sale receipts and invoices slips and must be use in order, this will make it easier when you have to use then for information which you will need now and later. When using the accrual method accounting recording system should always be put in a second Journal entry for the cash part at the time of the receipt and this accounting method only let you know when you count the revenue not how you got it.

Wednesday, October 23, 2019

Cause of Prejudice Essay

There are many types of prejudice in modern society. The definition of prejudice according to Webster’s Dictionary is â€Å"an adverse opinion or leaning formed without just grounds or before sufficient knowledge.† The causes of some prejudice can be linked to a person’s childhood. The effects of being prejudice can be harmful to the person who is prejudice and to the people or group that person is prejudice of. The causes of racial prejudice stem mainly from childhood. One way childhood can cause a person to be more prejudice is where that person lived as a child. For example, if a child lives in southern United States, that person is more likely to be more prejudice against African-Americans because their culture in the South has been more prejudice towards that group because it has had a prejudice toward that group in general for many years due to slavery. This is not to say that all people in the South are prejudice but it does lean more prejudice against that group. Whereas, in the northern states, there is less prejudice in general towards African-Americans. Another way childhood can affect whether or not a person has a prejudice is their family and how they were raised. If a child see’s their family or parents using racial slurs or putting down a race for any reason, that child could grow up to be the same way and think it is acceptable to have a prejudice. The effect of that could be going in public or at school using derogatory comments towards a race and thinking that it is alright and hurting someone’s feelings. Living in a household with more open views to other races allows for a child to be more open, show less prejudice to others, and be more accepting and tolerant. A child could also pick up prejudice opinions through their friends. Their friends could be bullying another child due to his race and that child could join along to fit in. This also is a major problem in schools because that child that is bullied could resent his classmates and this can cause many more problems down the road. If a child can learn to not fall into the peer pressure of bullying others for being different then more children could  follow and there is the solution to bullying in schools. Children are very impressionable and the more we can teach them about tolerance and to be more open to others than the better off as a society we are. With less prejudice there wouldn’t be as much violence because much of the violence that happens has some sort of prejudice attached with it. Also, the more open we are then the fewer problems we will have because everyone will get along and focus on more important issues of the world.